Special cabinet RFA
New wall-mounted cabinet RFA is designed to meet requests of small and middle firms. The cabinet is divided into three sections.
Section 1
19“ equipment with max. height of 6U and depth of 230 mm can be installed into the first section. The equipment is placed vertically and 19“ rails can be adjusted in predefined positions. Distribution power panel 230 V, adapters for active components or eventually for data incoming lines, are typical devices installed in this section.Section 2
The mounting width of 19“, height 12U and depth of 230 mm are at the disposal in the second section, where mounting rails are infinetely adjustable. Structured cabling system and active network components are usually concentrated in this section. Distribution of particular services to working places come out of this place. Recommended capacity is up to 48 working places (two ports for each according to the standards).Section 3
The third section occupies the whole area of cabinet rear side.
There is a place for equipment with max. dimensions of 19“, height
2U and depth 800 mm, installed vertically. Side perforated door on
the cabinet right side enables access to this section. Server 1U or
2U can be installed into this section. Enough place provided with
the side door allow extension of the whole server on the side (in
case of telescopic slides). It is necessary to consider sufficient
space from the both sides yet before installing. Because of server
installation on the right side and metal door of the first section
on the left side. Cooling of installed equipment can be supported
by installation of ventilators RAX-CH-X07-X9. There are two
break-out blanking panels in the left perforated door for it`s
mounting.
Breakout-type blanking panels
1. Cable openings covered with breakout-type blanking panels are ready in the top, bottom and rear part of the cabinet. Use a plastic frame and a blanking panel with a brush, that are parts of the cabinet supply, to seal the cabinet opening against dust penetration.2. There are two break-out blanking panels in the left metal door prepared for installation of cooling ventilators RAB-CH-X07-X1.
Supply
includes
Key - front door 2x
Screw 6x50 4x
Washer 6,6 4x
Dowel 10 4x
Captive nut M6 8x
Blanking panel with brush 1x
Material
Satefy hardened glass 5 mm thick
Steel sheet
19“ one-sectioned wall-mounted cabinet with IP 30 protection
Three 19'' sections
Cabinet is to be hanged right on the wall.
Cabinet components include two adjustable sliding vertical rails in each section.
Cabinet construction
– welded frame with removable side panels secured by locks
– glass door: safety hardened glass, thickness 5 mm
– metal door
Weight limit of the each door is max. 10 kg.
Minimal thickness of the surface finish treatment is 65 μm.
Cabinets are intended for installation of data and telecommunication devices and their distribution systems.
The frame of the cabinet and all the removable parts are connected with earthing cables that have to be properly fixed and inserted into connectors during all the time when using the cabinet.
There is one M8 screw placed on the bottom part of the cabinet as an earthing main point
Cable openings covered with breakout-type blanking panels are placed in the top and the bottom part of the cabinet rear side, others are in the top and the bottom side of cabinet.
Holes covered by break-out blanking panels, prepared for installation of 2 cooling ventilators, are placed in the metal door of the first section
Three 19'' sections
Cabinet is to be hanged right on the wall.
Cabinet components include two adjustable sliding vertical rails in each section.
Cabinet construction
– welded frame with removable side panels secured by locks
– glass door: safety hardened glass, thickness 5 mm
– metal door
Weight limit of the each door is max. 10 kg.
Minimal thickness of the surface finish treatment is 65 μm.
Cabinets are intended for installation of data and telecommunication devices and their distribution systems.
The frame of the cabinet and all the removable parts are connected with earthing cables that have to be properly fixed and inserted into connectors during all the time when using the cabinet.
There is one M8 screw placed on the bottom part of the cabinet as an earthing main point
Cable openings covered with breakout-type blanking panels are placed in the top and the bottom part of the cabinet rear side, others are in the top and the bottom side of cabinet.
Holes covered by break-out blanking panels, prepared for installation of 2 cooling ventilators, are placed in the metal door of the first section
