Hybrid cabinets SGA, SHA

 

Hybrid cabinets SHA

 

Hybrid cabinets for home data and power distribution systems
IP 20, loading capacity 30 kg

Cooling

The cabinet interior is cooled by ventilation perforations in the cabinet door.

Bonding

Made according to relevant standards.

Door lock

Double bit and other lock options ensure that the cabinet is securely locked.

Vertical mounting

The top half of the cabinet is fitted with sliding mounting brackets for 19“ patch panels or a fuse trough.

Horizontal mounting

Brackets are attached on the lower part of the cabinet for 19“ equipment.

Break-out panels

The top and bottom of the cabinet are fitted with wiring inputs covered with break-out panels.

Read more

 


SGA SGA

SGA - under plaster

TypeheightwidthdepthNumber of positions for vertical mountingNumber of positions for horizontal mountingWeight
 gross  (kg)
Weight
 net
(kg)

Maximum recommended load (kg)

 (mm)

SGA-077067015-XCD

770 670 150 4U 2U 15,7 15,4 30

 SHASHA

SHA - on wall

TypeheightwidthdepthNumber of positions for vertical mountingNumber of positions for horizontal mountingWeight
 gross (kg)
Weight
 net 
(kg)

Maximum recommended load (kg)

 (mm)

SHA-076062025-XCD

760 620 250 4U 2U 20,0 19,1 30



Description, usage

  • Hybrid wall cabinet with IP20/ IK07 protection.
  • The cabinet is hung directly on the wall (SHA); another option is the SGA, installed in a prepared space under the plaster.
  • The cabinets include two pairs of step-adjustable brackets with 19“ spacing.
  • Cabinet construction:
       – Welded frame from 1 mm thick sheet steel.
       – All steel door of 1 mm thickness with foam seals around the edge.
       – The cabinet door is connected to the frame by an earthing cable, which must be properly secured and inserted into the connectors for the entire duration of the cabinet's use.
  • Break-out caps in the upper and lower parts of the cabinet.
  • Maximum permissible load – cabinets: 30 kg; door: 4 kg.
  • Min. thickness of the surface finish is 65 μm.
  • These cabinets are intended for the use of data and telecommunication equipment and their distribution and power supply systems.
  • The frame of the cabinet and all removable parts (side and rear covers, doors…) are bonded with patch cables that have to be properly fixed and inserted into connectors throughout the period of use of the cabinet.
  • There is one M8 screw placed on the bottom part of the cabinet to connect the bonding.

More info

Operation conditions

Operation environment

  • the office
  • the cabinet is not intended for outdoor installations and for installations in environment that can negatively influence the functionality of the cabinet and the mounted devices (e.g. environment with danger of explosion or humid and wet surroundings).

Must be protected against

  • mechanical damage,
  • improper handling,
  • a different usage than the cabinet is intended for.

Improper handling is especially

  • overloading (exceeding the maximum recommended load),
  • device installation that can negatively influence the operation and function of the cabinet or the installed equipment,
  • change of the construction or design of the cabinet.

Installation of the cabinet

  • To ensure the maximum recommended load, it is necessary to distribute the load evenly.
  • Place the cabinet on a flat floor and adjust any differences using levelling feet.
  • To avoid dust penetration in case the cables lead through some of the cable openings, it is possible to sealed it using a blanking panel with a brush and equip it with a hem edge (both are included in the supply).

Environmental protection

  • All parts are made of recyclable materials and after decommissioning the cabinet, they must be disposed of according to relevant regulations.

Certificate and conformity

  • This product is fully in accordance with ČSN EN 62208 ed. 2 (357040), (EN 62208:2011), (idt IEC 62208:2011).

Photogallery

Photogallery of Hybrid cabinets SGA, SHA

>> more photos